HR Smith Products

HR Smith Products (14)

Friday, 07 June 2013 13:14

13-150-3

Written by

13-150-3 vehicle antennaThe 13-150 series of antennas offers significally reduced visual profile with electrical performance comparable to passive antennas more than twice the size. These antennas are adaptable to multi band frequency requirements with added UHF functionality already acheived within the same footprint.


System Operation
The 13-150 series of antennas utilise advance high speed switching circuitry techniques to achieve high levels of gain performance. This is made possible by each antenna holding an individually programmed EPROM memory device which can store a unique set of antenna calibration data pre-defined for the finalised platform. When the radio is tuned to a frequency it sends a frequency word to the internal Logic Converter Unit, this word is then deciphered into a binary format and enables the antenna to switch to the sent frequency. (All of this process happens in <50 microseconds) As the antenna holds all the calibrated frequency data it enables any antenna to work on any platform without the antenna having to return to the factory.

  •     Low Visual Profile <1 metre
  •     Spring mounted on a NATO four hole base
  •     Specifically designed for use on land and sea
  •     based vehicles
  •     Fast silent tuning less than 50 microseconds
  •     Compatible with frequency hopping
  •     secure speech networks
  •     Unique memory system (allowing 'in theatre'
  •     part swap)
  •     Multi band operation
  •     Out of band signal filtering
  •     50 W CW Power Handling (VTAC)
Specification
Typical radio interfaces
Frequency 30-90MHz (VTAC)
  225-450MHz (UHF)
Impedance 50 Ohms
V.S.W.R. ≤ 3.0:1 VHF and UHF
Polarisation Vertical
Radiation Omni
RF Connectors Two(2) TNC Female
DC Connectors MIL Series II
  62GB 12E14-19PN
Colours Nato Green
  Black
  (other colours available on request)
Environmental Qualifications: Tested and qualified to MIL-STD 810E
Typical Radio Interfaces Rockwell Collins Flexnet Series
  Rhode & Schwarz M3AR
  Raytheon ARC231 and 232
  Thales TRA5400N
  Elmer SRT651 Series
  Wulfsburg RT5000
  Marconi AD3400
  (Compatible with other radio types on request)
Installation Good electrical contact must be maintained between the antenna base and the vehicle shell
Vendor Code (NSN) K6543
Thursday, 30 August 2012 10:17

New 406 MHz Ejection Seat Compatible PLB

Written by

The 500-30 is the latest member of the highly successful Techtest PLB range offering 406MHZ transmission and Guard frequency transmission combined with embedded GPS to500-30 provide positional accuracy of ≤100m.

With both manual and automatic activation capability the beacon offers maximum flexibility across a fleet of aircraft. Providing interface solutions for inclusion in PSPs within ejection seats such as ACES II/III and in combination with parachute activation mechanisms such as the BA22. Once activated upon ejection the PLB will transmit SAR frequency signals via remote antennas allowing rapid recovery.

Once on the ground aircrew can continue to transit using remote or integrated dual frequency antennas including GPS providing portable functionality and the ability to control beacon transmission according to circumstance. With 5 year battery life, 48 hours transmission on 121.5MHz and 24hours on 406MHz at −20°C the 500-30 meets COSPAS SARSAT, ED-62A, STANAG 7007 and MIL-STD 810F specifications.

 

Transmitter Signal
The PLB transmits modulated signals on 121.5MHz distress frequency with characteristics in accordance with STANAG 7007, plus 406MHz in accordance with COSPAS/SARSAT.
Modulation (121.5MHz)
Continuous Swept Tone of at least 700Hz within the Sweep Range.
Sweep Range 1.6KHz to 300Hz
Sweep Rate 2-3Hz
Amplitude Modulated with Rectangular Wave
Modulation Depth 80% minimum
Modulation (406MHz)
0.5 Secs 5W pulse every 50 secs.
Phase modulation of ±∏/3 rad (peak)
Digital modulation (see C/S G.005 Iss. 2 Rev 1, Section 3) to include:
• Bit Synchronisation • Frame Synchronisation
• Protected Field • Emergency-Code/National Use Field
• Long Message  
GPS Receiver (Embedded)
Hot Start (avg) <9 sec Sat. Signal Reacquisition Time 100ms
Warm Start (avg) <35 sec Number of Channels 12
Cold Start (avg) <39 sec Min Signal Level Tracked -172dBw
Receiver L1 C/A Code Power Consumption 82mW
Protocols NMEA  
Power Output
406MHz 24 hours min 5W (+37dBm ±2dBm) at -20˚C
121.5MHz 48 hours min >50mW (+17dBm) at -20˚C
Mechanical
Activation Lanyard
  Manual ARM/OFF SWITCH
  Automatic BA22 Interface / ACLS33 ASSY
Dimensions 125mm x 70mm x 33mm nominal
Weight <587g nominal
Colour NATO green
The unit is designed to survive for up to 20 years with the only maintenance being battery replacement every five years.
Compliance
The PLB is compliant with the following specifications:
Civil EUROCAE ED62A / RTCA DO-204A
  EUROCAE ED14F/RTCA DO-160F/
COSPAS / SARSAT
Military NATO - STANAG 7007 / MIL STD 810F
Part Number
500-30 121.5, 406 & GPS
Wednesday, 29 August 2012 15:41

Direction Finding S.A.R.

Written by

direction finding sar

  • Multi-beacon DF
  • Single compact antenna unit
  • High sensitivity receiver
  • Fully COSPAS-SARSAT compatible

The Techtest DF system is designed to reduce the time to locate emergency locator beacons. It is compatible with both 121.5MHz swept tone distress beacons and 406MHz COSPAS-SARSAT transmissions on current and future frequencies.

The user is able to monitor four frequencies and detect emergency transmissions. Each transmission is allocated a unique identification which can then be selected for more detailed information.

For 121.5MHz the system can display relative bearing details.

For 406MHz the system will give all the same information as 121.5MHz but in addition will record and decode the COSPAS-SARSAT message, giving details of the distress beacon and if available the GPS beacon location.

The system comprises of three modules

  • 1. Antenna (10-246-1) The Antenna is a single compact module comprising a circular array of elements with integral high sensitivity receivers. The array is designed todf control panel give optimal angular resolution of the emitters.
  • 2. Control Unit (406-28) The Control Unit takes the array output and, using a digital processing and advanced beam forming technique, is able to discriminate multiple emitters and direction find on the signals. All the data is processed using intelligent algorithms to reduce system noise and spurious responses.
  • 3. Display (407-3) Different display options are available and are platform specific. The basic display module is based on the Techtest 407-2 unit. This unit is designed for ease of use featuring mode and scroll controls and a dual function uncluttered graphic LCD display. A secondary display option is available.

Detection
In normal operating mode the DF receiver frequency is switched cyclically between 121.5, 156.8 and 243 MHz. If a signal above the threshhold is detected, a 0.3 second snapshot is recorded before continuing. A separate receiver is used to continuously monitor the 406 SARSAT frequency. If a signal is detected then the DF receiver will immediately switch to 406MHz frequency and record a snapshot. In the event of transmitting beacons incorporating a GPS position, the system will display the applicable lat/long co-ordinates.

Direction Finding / Homing
A 360˚ direction finding facility is provided giving a direction for the aircraft to fly to the transmitting beacon. No other navigation aids are required. If however on board GPS navigation systems are installed in the aircraft, system integration will provide aircrew with both an absolute bearing and distance information to the transmitting beacon.
In the Homing mode the system sequentially scans the distress frequencies and provides a visual display of left/right steer information.

Cockpit Controller / Indicator
The controller / indicator is mounted in the cockpit. There are just two controls : a push button mode selector (switching between Decode and DF modes), a rotary click / push selector providing control of menu options. The unit is designed to operate mainly without user input.
The user can select any of three modes:

  • i)    Left-Right Indicator: To show bearing relative to aircraft heading.
  • ii)   Map display: Showing relative positions, (or bearings), of all detected emitters, both from DF receiver and 406 Decoder.
  • iii)  Text Display: Ideal for 406 decoder information. Can also be used to display range and bearing data.pdf icon
Dimensions Short 3/8 ATR (90x198x322mm)
SAR frequencies 121.5, 243, 156.8, 406 MHz
Training frequencies 4 selectable: 110 to 410 MHz
Sensitivity 2.5μV
DF Accuracy Better than 5˚
Decoder Frequency 406.025 - 406.050 MHz
Message Format COSPAS-SARSAT C/S T.001
Supply Volts 18-36V DC MIL-STD 704D
Antenna 10-246-1
Diameter 250mm
Height Standard 250mm
Reduced 180mm
Polarisation Vertical
Cockpit Controller / Indicator 406-3
Dimensions 146 x 67 x 152mm
LCD Display 56 x 42mm (320 x 420 pixels)
Backlighting NVIS Green B (MIL-STD 3009)
Environmental MIL-STD 810F
EMI/EMC MIL-STD 461 F
Thursday, 15 December 2011 10:49

406 Handheld Decoder

Written by
The 12-406-9 is a handheld 406 decoder that receives and decodes COSPAS SARSAT distress or test messages. The unit can be set-up to monitor all transmissions (including tests) or distress only.hr smith 406 decoder
  • COSPAS/SARSAT 406MHz Detection and Decoding
  • Messages decoded and displayed in an easy to understand format
  • Touch screen interface
  • Internal Antenna
  • Internal re-chargeable battery
  • USB to PC connectivity
The need to detect and locate downed aircrew has always existed. Accurately pin pointing both aircraft and crew can sometimes necessitate a lengthy search scenario. The increased population of COSPAS /SARSAT (C/S) 406MHz beacons worldwide is aiding the task significantly. In particular, for those able to transmit with embedded GPS, the potential is there for the land or airborne Search and Rescue (SAR) forces to affect immediate rescue.

The Techtest 12-406-9 is specifically designed to detect, locate, and verify any 406MHz beacon transmission, including ELT or ADELT/CPI and EPIRBs. It can be used either as a test tool on the ground or as portable equipment on a SAR mission.  It is able to immediately display the transmitted GPS Lat/Long location of the beacon if present and, in conjunction with the built in GPS receiver, display range and bearing information.

The handheld unit includes a colour touch screen providing a clear display of information with user configurable fields. The integral antenna results in a compact device easy to carry. Data is updated continuously as new messages are received and decoded (typically every 50 seconds from one beacon). If multiple beacons are transmitting then all are summarized on a scrolling display. Individual messages can be selected to display full decode information. Data can be transferred to a PC for later analysis.

The unit can be fixed to a wall, using an optional mounting tray, and configured as a remote monitoring station.  In this case data is logged automatically by a Windows Based Application.
 
pdf406-decoder-12-406-9
 
 
Monday, 04 October 2010 15:27

Test Equipment

Written by

12-602-8 cable antenna analyzerAs manufacturers of antennas and SAR equipment, the company has always believed it of great importance to provide supporting equipment to these products. Over the years, this has resulted in a range of Test Sets being manufactured by Techtest.

Our range of VSWR Test Sets is known throughout the aviation community as the industry standard products for testing aircraft antennas. They are all available with ruggedized cases and models are available to cover all the frequencies commonly found in avionic equipment. These VSWR Test Sets allow antennas to be checked for correct operation and can be used whilst the antenna is still on the airframe thus saving costly removal of the antenna when it is not necessary.

It is vital that an Emergency Locator Transmitter works correctly, if it is used, so Techtest supply a range of test equipment to check correct operation of this type of equipment. These Test Sets can be used with all types and makes of ELTs and EPIRBs.

Brochure downloads

pdf12-602-8 Antenna and Cable Analyzer (PDF)  
pdf12-406 Homing Test Set (PDF, 436Kb)
pdf12-500-5 PLB / ELT Test Set (PDF, 60Kb)
pdf12-503-1 PLB / ELT Test Set (PDF, 60Kb)
pdf12-503-5 Programming Test Set (PDF, 84Kb)
pdf12-612 Electrostatic Discharger Test Set (PDF, 840Kb)
Monday, 04 October 2010 15:09

Homing Systems

Written by

The need for Search and Rescue (SAR) services to accurately detect and locate the distress signals from emergency beacons resulted in Techtest developing its range of Homing Systems.

These use a phase comparison method to provide left-right steering information, to the SAR pilot enabling him to locate emergency beacons operating on all the standard distress frequencies (121.5 MHz, 156.8 MHz, 243 MHz and 406 MHz). This type of system requires only two antennas and offers a more compact, lower cost solution to the more complex DF systems available.

 Techtest now manufactures a range of Homer/Decoder systems which decode the unique data included in the COSPAS-SARSAT 406 MHz distress signal. This includes the position infor406-2-053 homing systemsmation from Location Protocol Beacons and gives the user real time information to help minimise rescue times. A number of integrated airborne systems are available as well as the unique Portable 406 SAR Decoder which is a fully self contained unit which can be carried on to any aircraft, boat or land vehicle. This unit is ideal for a SAR force which already has Homing/DF systems fitted but wishes to extend its capability to include 406 MHz decoding in a cost effective way.

Brochure downloads

pdf12-406-7 Portable 406 SAR Decoder (PDF, 160Kb)
pdf12-406 Homing Test Set (PDF, 436Kb)
pdf406-2-053 Full NVIS Compatibility SAR Homing System (PDF, 284Kb)
pdf406-407 Delivering real-time SAR 406 decode and position (PDF, 520Kb)

Monday, 04 October 2010 14:43

Automatic ELT

Written by

503 seriesThe 503 Series of automatically activated Emergency Locator Transmitters are the most advanced on the market yet are available at competitive prices. All 503 series Emergency Locator Transmitters are designed to work with the COSPAS-SARSAT emergency satellite system and operate on 406 MHz in addition to the two traditional distress frequencies of 121.5 MHz and 243 MHz.

They are available as an Automatic Fixed Emergency Locator Transmitter or Automatic Portable Emergency Locator Transmitter depending on which mounting tray is specified. The 503 series of Emergency Locator Transmitters has been fitted on all types of platform including GA aircraft, helicopters, commercial airliners and military fast jets.

503 seriesBy using the latest in solid state microprocessor technology coupled with an advanced battery design, we have developed the smallest and lightest automatic Emergency Locator Transmitter currently available. This has not been achieved at the expense of the outright specification of the Emergency Locator Transmitters as they offer a number of unique standard features and options. They are the only Class 1 Automatic Emergency Locator Transmitter available ensuring they remain fully functional down to temperatures of -40°C. They also include a sophisticated self-diagnosis feature which along with their modular design ensures trouble free maintenance.

The 503 series of Emergency Locator Transmitters can be interfaced to the aircraft’s on board GPS system, without a separate interface unit, to ensure even faster detection times in the event of an emergency. All common GPS protocols are supported, and for aircraft not fitted with GPS the 503 series of Emergency Locator Transmitters can be specified with its own embedded GPS card.

Techtest are the leading manufacturer of Automatic Deployable Emergency Locator Transmitters, supplying all the leadingcpi control panel helicopter manufacturers and off shore operators. These systems are part of our 503 series and offer a top quality solution for all maritime aircraft whether commercial or military.

Brochure downloads

pdf503 Series Emergency Locator Transmitters (PDF, 900Kb)
pdfCrash Position Indicator, 503 Series of Deployable Beacon (PDF, 192Kb)
pdf12-503-5 Programming Test Set (PDF, 84Kb)

Monday, 04 October 2010 14:21

ELT / PLB

Written by

500-27-07

The 500 series of Personal Locator Beacons or Survival Emergency Locator Transmitters offers a wide range of options to suit any requirement. The 500 series of Personal Locator Beacons has been chosen by a wide customer base, including armed forces, commercial airlines, off-shore helicopter operators, life raft manufacturers and ejection seat manufacturers.

For all the 500 series Personal Locator Beacons, Techtest has obtained full certification to aircraft standards so these products should not be confused with inferior quality beacons intended for hobby use.

The 500-1 Personal Locator Beacon is a compact light-weight unit operating on 121.5 MHz and 243 MHz and has been favoured by customers requiring a small beacon for many years.

The 500-12 Personal Locator Beacon is designed to work with the COSPAS-SARSAT search and rescue satellite system and features 406 MHz as well as 121.5 MHz and 243 MHz distress signals. It also incorporates a speech function which allows survivors to have two way voice communication with a rescue craft. In addition to the normal aircraft approvals the 500-12 also has full Boeing and Airbus approvals making it the natural choice for commercial airline operators due to its compact size and low weight. The 500-27 shares all the functionality of the 500-12 but also incorporates embedded GPS to minimize location time in the event of an emergency.

The latest 500-27-07 PLB (above right) utilizes all the proven electronics of its predecessors but updates the casing design to give a modern stylish appearance without losing the rugged and durable qualities associated with Techtest SAR products.

The new 500-32 PLB (above left) offers similar features to the 500-27-07 but in a significantly smaller package (35% reduction in volume). This has been achieved by using state-of-the-art battery technology and optimised electronics.

After rigorous testing the 500-32 series of ELT(s) or PLB has recently been awarded a COSPAS SARSAT type approval (Certificate No. 223).

500-30, 406 MHz Ejection Seat Compatible PLB

The 500-30 is the latest member of the highly successful Techtest PLB range offering 406MHZ transmission and Guard frequency transmission combined with embedded GPS to500-30 provide positional accuracy of 100m.

With both manual and automatic activation capability the beacon offers maximum flexibility across a fleet of aircraft. Providing interface solutions for inclusion in PSPs within ejection seats such as ACES II/III and in combination with parachute activation mechanisms such as the BA22. Once activated upon ejection the PLB will transmit SAR frequency signals via remote antennas allowing rapid recovery.

Once on the ground aircrew can continue to transit using remote or integrated dual frequency antennas including GPS providing portable functionality and the ability to control beacon transmission according to circumstance. With 5 year battery life, 48 hours transmission on 121.5MHz and 24hours on 406MHz at -20 °C the 500-30 meets COSPAS SARSAT, ED-62A, STANAG 7007 and MIL-STD 810F specifications.

 

Brochure downloads

pdf500-12 Multi Function Personal Locator Beacon
pdf500-27 Multi Function Personal Locator Beacon + Embedded GPS
pdf500-27-07 Multi Function Personal Locator Beacon + Embedded GPS
pdf500-30 Multi Function Personal Locator Beacon
pdf500-32 406MHz Multi Function Personal Locator Beacon
pdf12-503-5 Programming Test Set

Monday, 04 October 2010 14:11

Static Dischargers

Written by

dischargersFor many years, HR Smith (Technical Developments) have been manufacturing a range of Static Dischargers for all aircraft platforms from GA aircraft through commercial airliners to fast jet applications.

The company manufactures a version of its range of dischargers by conventional techniques using aluminium castings with composite rods but has pioneered the introduction of its range of all plastic static dischargers. This type of discharger is manufactured from advanced thermo-set plastics and offers a number of advantages over the conventional design. These include light weight, improved noise resistance, lightning strike resistance and low cost of ownership.

Brochure downloads

pdf12-612 Electrostatic Discharger Test Set (PDF, 840Kb)
pdfA revolutionary advance in electrostatic dischargers (PDF, 1Mb)

Monday, 04 October 2010 13:47

Gaskets

Written by

hr smith gasketsModern electrical and RF systems require that joints between metallic surfaces remain in good electrical contact and free from corrosion. To ensure this, HR Smith (Technical Developments) has developed a range of conductive sealing gaskets.

The “wet-fit” range use a thin sheet of aluminium alloy or nickel alloy and a two-part epoxy resin to give the ultimate in corrosion resistance while still retaining high electrical conductivity. The gasket can be stamped out in any shape and can be purchased separately from the sealant or can be supplied as a kit with the sealant.

The company designed, and obtained a world-wide patent on its “dry-fit” range of gaskets. These gaskets again use aluminium or nickel alloy sheet but the sheet is sandwiched between two sheets of polyethylene foam. This means there is no requirement for a sealant and fitting is simpler and less time consuming. The “dry-fit” gasket still provides excellent corrosion protection and due to the unique way it is stamped provides electrical continuity.

Brochure downloads

pdf10-500-11 Conductive Sealing Gaskets (PDF, 360Kb)
pdf10-500-11 Conductive Sealing Gaskets Technical Data (PDF, 760Kb)
pdf10-500-11A Dry Fit Conductive Anti-Corrosion Gaskets (Airborne Antenna Brochure) (PDF, 3.1Mb)